Please wait a minute...
中国腐蚀与防护学报  2005, Vol. 25 Issue (4): 241-244     
  研究报告 本期目录 | 过刊浏览 |
几种因素对油套管钢CO2腐蚀行为影响
李建平;赵国仙;郝士明
东北大学材料治金学院
DYNAMIC CORROSION BEHAVIORS OF N80,P105 AND SM110 STEEL
Jianping Li;Guoxian Zhao;
东北大学材料治金学院
全文: PDF(129 KB)  
摘要: 研究了流动条件下CO2分压、流速、原油含水率、溶液Cl-浓度及pH值对3种油套管常用材料N80、P105和SM110腐蚀行为的影响。90℃、1.5m/s时,随CO2分压升高,材料的腐蚀速率先升后降,在CO2分压为2.5MPa时,除N80钢外,其它材料的腐蚀速率达到最大值;90℃、CO2分压为2.5MPa时,随着流速成的增加,腐蚀速率先升后降,在流速为1.5m/s时,材料的腐蚀速率达到最大值;原油含水率对材料的腐蚀速率影响较大;溶液的pH值及Cl-浓度对材料的腐蚀速率影响不明显。
关键词 腐蚀油套管钢温度流速油水比CO2腐蚀    
Abstract:The effect of CO2 partial pressure , flow velocity , water cut,Cl- concentration and pH of solutions on the corrosion behaviors of n80, P105 and SM110 steel were studied. When the temperature was 90℃ and flow velocity was 1.5m/s, corrosion rate increased early and decreased lately with CO2 partial pressure increasing, when CO2 partial pressure was 2.5MPa, corrosion rates of materials investigated except N80 steel reached maximal value. When the temperature was 90℃ and CO2 prtial pressure was 2.5 MPa, corrosion rate increased early and decreased lately with flow tate increasing, being maximal at 1.5m/s flow velocity. Water cut sharply influenced the corrosion rate. The effect of pH and Cl- concentration on the corrosion rate were unobvious.
Key wordscorrosion    tube and case steel    temperature    flow rate    water cut    CO2 corrosion
收稿日期: 2004-04-01     
ZTFLH:  TG172  
通讯作者: 李建平     E-mail: Lijianp@yahoo.com.cn
Corresponding author: Jianping Li     E-mail: Lijianp@yahoo.com.cn

引用本文:

李建平; 赵国仙; 郝士明 . 几种因素对油套管钢CO2腐蚀行为影响[J]. 中国腐蚀与防护学报, 2005, 25(4): 241-244 .
Jianping Li, Guoxian Zhao. DYNAMIC CORROSION BEHAVIORS OF N80,P105 AND SM110 STEEL. J Chin Soc Corr Pro, 2005, 25(4): 241-244 .

链接本文:

https://www.jcscp.org/CN/      或      https://www.jcscp.org/CN/Y2005/V25/I4/241

[1]LiJP,ZhaoGX,HaoSM.Thestudyonstaticcorrosionofoil thimbleusedinTarimoilfield[J].J.Chin.Soc.Corros.Prot.,2004,24(4):230-233(李建平,赵国仙,郝士明.塔里木油田用油套管钢的静态腐蚀[J].中国腐蚀与防护学报,2004,24(4):230-233)
[2]CarlosA,PalaciosT.Applicationofsimulationoftechniquesforin ternalcorrosionprediction[A].Corrosion/97[C].Houston:NACE,1997,2
[3]NesiS,JohnP,VrhovaM.CO2corrosionofcarbonsteel-from mechanismtoempiricalmodelling[J].CorrosionReviews,1997,15:112-126
[4]GrayLGS.Mechanismofcarbonsteelcorrosioninbrinescontain ingdissolvedcarbondioxideatpH4[A].Corrosion/89[C].Houston:NACE,1989,464
[5]GrayLGS.EffectofpHandtemperatureonthemechanismofcar bonsteel[A].Corrosion/98[C].Houston:NACE,1998,40
[6]VeraJR.FlowVelocityEffectonCO2CorrosionofCarbonSteel UsingaDynamicFieldTester[M].London:EuropeCorrosionFed eration,1994,94-119
[7]ZhangXY,DiC,LeiLC.CorrosionandControlforDioxide[M].Beijing:ChemicalIndustryPress,2000,57(张学元,邸超,雷良才.二氧化碳腐蚀与控制[M].北京:化学工业出版社,2000,57)2
[1] 郑黎, 王美婷, 于宝义. 镁合金表面冷喷涂技术研究进展[J]. 中国腐蚀与防护学报, 2021, 41(1): 22-28.
[2] 于宏飞, 邵博, 张悦, 杨延格. 2A12铝合金锆基转化膜的制备及性能研究[J]. 中国腐蚀与防护学报, 2021, 41(1): 101-109.
[3] 董续成, 管方, 徐利婷, 段继周, 侯保荣. 海洋环境硫酸盐还原菌对金属材料腐蚀机理的研究进展[J]. 中国腐蚀与防护学报, 2021, 41(1): 1-12.
[4] 唐荣茂, 朱亦晨, 刘光明, 刘永强, 刘欣, 裴锋. Q235钢/导电混凝土在3种典型土壤环境中腐蚀的灰色关联度分析[J]. 中国腐蚀与防护学报, 2021, 41(1): 110-116.
[5] 韩月桐, 张鹏超, 史杰夫, 李婷, 孙俊才. 质子交换膜燃料电池中TA1双极板的表面改性研究[J]. 中国腐蚀与防护学报, 2021, 41(1): 125-130.
[6] 张雨轩, 陈翠颖, 刘宏伟, 李伟华. 铝合金霉菌腐蚀研究进展[J]. 中国腐蚀与防护学报, 2021, 41(1): 13-21.
[7] 冉斗, 孟惠民, 刘星, 李全德, 巩秀芳, 倪荣, 姜英, 龚显龙, 戴君, 隆彬. pH对14Cr12Ni3WMoV不锈钢在含氯溶液中腐蚀行为的影响[J]. 中国腐蚀与防护学报, 2021, 41(1): 51-59.
[8] 左勇, 曹明鹏, 申淼, 杨新梅. MgCl2-NaCl-KCl熔盐体系中金属Mg对316H不锈钢的缓蚀性能研究[J]. 中国腐蚀与防护学报, 2021, 41(1): 80-86.
[9] 王欣彤, 陈旭, 韩镇泽, 李承媛, 王岐山. 硫酸盐还原菌作用下2205双相不锈钢在3.5%NaCl溶液中应力腐蚀开裂行为研究[J]. 中国腐蚀与防护学报, 2021, 41(1): 43-50.
[10] 史昆玉, 吴伟进, 张毅, 万毅, 于传浩. TC4表面沉积Nb涂层在模拟体液环境下的电化学性能研究[J]. 中国腐蚀与防护学报, 2021, 41(1): 71-79.
[11] 贾世超, 高佳祺, 郭浩, 王超, 陈杨杨, 李旗, 田一梅. 再生水水质因素对铸铁管道的腐蚀研究[J]. 中国腐蚀与防护学报, 2020, 40(6): 569-576.
[12] 赵鹏雄, 武玮, 淡勇. 空间分辨技术在金属腐蚀原位监测中的应用[J]. 中国腐蚀与防护学报, 2020, 40(6): 495-507.
[13] 刘晓, 王海, 朱忠亮, 李瑞涛, 陈震宇, 方旭东, 徐芳泓, 张乃强. 电站用奥氏体耐热钢HR3C与Sanicro25在超临界水中的氧化特性[J]. 中国腐蚀与防护学报, 2020, 40(6): 529-538.
[14] 马鸣蔚, 赵志浩, 荆思文, 于文峰, 谷义恩, 王旭, 吴明. 17-4 PH不锈钢在含SRB的模拟海水中的应力腐蚀开裂行为研究[J]. 中国腐蚀与防护学报, 2020, 40(6): 523-528.
[15] 岳亮亮, 马保吉. 超声表面滚压对AZ31B镁合金腐蚀行为的影响[J]. 中国腐蚀与防护学报, 2020, 40(6): 560-568.