Please wait a minute...
中国腐蚀与防护学报  2026, Vol. 46 Issue (2): 405-416     CSTR: 32134.14.1005.4537.2025.131      DOI: 10.11902/1005.4537.2025.131
  研究报告 本期目录 | 过刊浏览 |
模拟硫污染海水环境下交变氧含量对B30铜镍合金腐蚀行为的影响机制研究
练龙江1, 陈思敏1, 黄延淞1, 曾兰香1, 郑中2, 雷冰1(), 孟国哲1
1.中山大学化学工程与技术学院 珠海 519082
2.武汉第二船舶设计研究所 武汉 430064
Effect of Alternating Dissolved Oxygen Content on Corrosion Behavior of B30 Cu-Ni Alloy in a Simulated Sulfide-polluted Seawater Environment
LIAN Longjiang1, CHEN Simin1, HUANG Yansong1, ZEN Lanxiang1, ZHENG Zhong2, LEI Bing1(), MENG Guozhe1
1.School of Chemical Engineering and Technology, Sun Yat-sen University, Zhuhai 519082, China
2.Wuhan Second Ship Design & Research Institute, Wuhan 430064, China
引用本文:

练龙江, 陈思敏, 黄延淞, 曾兰香, 郑中, 雷冰, 孟国哲. 模拟硫污染海水环境下交变氧含量对B30铜镍合金腐蚀行为的影响机制研究[J]. 中国腐蚀与防护学报, 2026, 46(2): 405-416.
Longjiang LIAN, Simin CHEN, Yansong HUANG, Lanxiang ZEN, Zhong ZHENG, Bing LEI, Guozhe MENG. Effect of Alternating Dissolved Oxygen Content on Corrosion Behavior of B30 Cu-Ni Alloy in a Simulated Sulfide-polluted Seawater Environment[J]. Journal of Chinese Society for Corrosion and protection, 2026, 46(2): 405-416.

全文: PDF(17981 KB)   HTML
摘要: 

针对舰船B30 合金材料服役期间在海水贫氧-富氧交替和S2-污染环境下的腐蚀问题,本文结合极化曲线、电化学阻抗等方法,系统研究了模拟S2-污染与氧含量交替变化海水环境下B30合金的腐蚀行为及反应机制。结果表明,在模拟洁净海水环境下,溶解氧主要发挥促进成膜作用,随氧含量增加,B30合金表面膜层保护性增强,其耐蚀性顺序为:富氧>交变含氧>贫氧;而在模拟S2-污染的海水环境下,B30合金耐蚀性规律变为:富氧>贫氧>交变含氧,其中含硫且“贫氧-富氧”交替条件下B30合金腐蚀最为严重,表现为腐蚀电流密度显著增加、电化学阻抗大幅下降、极化电阻明显降低,以局部点蚀为主要特征,表面膜层出现严重开裂与脱落现象,腐蚀泄漏风险显著提升。机理分析认为,在含S环境下,B30合金的表面膜质量因S2-作用而劣化,交变含氧条件打破了O2主导的“成膜-溶解”动态平衡,O2在B30合金局部膜破损处的促进腐蚀作用占主导,增强了B30合金的局部腐蚀倾向。

关键词 B30铜镍合金S2-交变含氧腐蚀机制    
Abstract

To address the corrosion issues of B30 alloy for ships during service in conditions such as S2--polluted seawaters while with conditions of alternating changes in oxygen content, herein, the corrosion behavior and reaction mechanisms of B30 alloy in S2- polluted simulated seawaters with alternating changes in oxygen content were studied via methods such as polarization curves and electrochemical impedance spectroscopy (EIS). The results show that in a simulated clean seawater, the dissolved oxygen acts mainly as accelerant for the formation of passivation film. As the oxygen content increases, the protective properties of the surface film on B30 alloy were enhanced, and the influence degree of oxygen content on the corrosion resistance of B30 alloy may be ranked as follows: high-oxygen > alternating oxygen > low-oxygen. However, in simulated S2--polluted seawater, the influence order of oxygen content changes to: high-oxygen > low-oxygen > alternating oxygen. In the condition of alternating changes in oxygen content, B30 alloy experiences the most severe corrosion, characterized by a significant increase in corrosion current density, a substantial decrease in electrochemical impedance, a marked reduction in polarization resistance, and the predominance of localized pitting. Correspondingly, the surface film exhibits serious cracking and delamination, leading to a significantly increased risk of localized corrosion and leakage. Mechanism analysis indicates that in sulfur-containing environments, the quality of surface film on B30 alloy was deteriorated due to the action of S2-. Alternating oxygen conditions disrupt the dynamic equilibrium of oxygen-dominated "film formation-dissolution" processes, allowing O2 to dominate the corrosion acceleration at local film damage sites, thus enhancing the alloy's susceptibility to localized corrosion.

Key wordsB30 copper-nickel alloy    sulfur ion    alternating content of dissolved oxygen    corrosion mechanism
收稿日期: 2025-04-29      32134.14.1005.4537.2025.131
ZTFLH:  TG174  
通讯作者: 雷冰,E-mail:leibing@mail.sysu.edu.cn,研究方向为腐蚀电化学
作者简介: 练龙江,男,2001年生,硕士生
图1  实验所用B30合金的金相组织
NumberContent design of S2- and dissolved oxygenCode
133 mg/L O2, without Na2SA
21 mg/L O2, without Na2SD
3(1 mg/L→33 mg/L→1 mg/L→33 mg/L…), without Na2SD-A
433 mg/L O2, 5 mg/L Na2SA-S
51 mg/L O2, 5 mg/L Na2SD-S
6(1 mg/L→33 mg/L→1 mg/L→33 mg/L…), 5 mg/L Na2SD-A-S
表1  模拟环境特征以及对应代号
图2  模拟硫污染环境浸泡及电化学实验装置及交变溶解氧实验设计流程图
图3  模拟洁净海水中,不同氧含量条件下B30合金浸泡8 d后的电化学阻抗谱
图4  模拟硫污染海水中,不同氧含量条件下B30合金浸泡8 d后的电化学阻抗谱
图5  无硫环境下交替氧含量(D-A)时B30合金浸泡不同时间的电化学阻抗谱
图6  含硫环境下交替氧含量时B30合金浸泡不同时间的EIS谱
图7  不同环境下B30合金的低频模值变化随浸泡时间的变化
图8  B30合金在不同环境浸泡8 d时的动电位极化曲线
ParametersEcorr, SCE / mVIcorr / μA·cm-2
A-214.00.35
D-325.70.34
D-A-283.60.32
A-S-311.40.84
D-S-328.31.37
D-A-S-126.04.89
表2  B30 合金在不同环境中的极化曲线拟合数据
图9  B30合金在不同环境中浸泡8 d时的线性极化曲线
图10  B30合金在不同环境中浸泡8 d后表面的宏观形貌以及对应的微观形貌
图11  交变含氧含硫环境中B30 合金浸泡30 d后表面腐蚀的宏观、微观形貌及能谱分析
图12  在交变含氧含硫环境中B30 合金浸泡30 d后表面腐蚀的截面形貌以及去除腐蚀产物后的表面形貌
图13  B30合金在不同环境浸泡8 d后合金表面的XPS谱
图14  B30 合金在不同环境中浸泡8 d后试样表面的Cu 2p、Ni 2p、Fe 2p和S 2p谱
CodeCorrosion products
ACu(OH)2, Ni(OH)2, FeOOH
A-SCu2S, Na2SO4, Cu2O, NiO, Cu(OH)2, Ni(OH)2, FeOOH
D-SCu2S, FeS2, Na2S, CuS, S, Cu2O, FeOOH, Na2SO4
D-A-SCuS, Na2SO4, CuO, NiO, Cu(OH)2, Ni(OH)2, FeOOH
表4  不同环境浸泡8 d后B30合金表面腐蚀产物
[1] Chen H L, Ma L, Huang G S, et al. Effects of pH value, temperature and salinity on film formation of B30 Cu-Ni alloy in seawater [J]. J. Chin. Soc. Corros. Prot., 2023, 43: 481
[1] 陈翰林, 马 力, 黄国胜 等. pH值、温度和盐度对B30铜镍合金在海水中成膜的影响 [J]. 中国腐蚀与防护学报, 2023, 43: 481
[2] Xing S H, Liu J Z, Bai S Y, et al. Influence of seawater flow speed on galvanic corrosion behavior of B10/B30 alloys coupling [J]. J. Chin. Soc. Corros. Prot., 2023, 43: 391
[2] 邢少华, 刘近增, 白舒宇 等. 海水流速对B10/B30电偶腐蚀行为影响规律研究 [J]. 中国腐蚀与防护学报, 2023, 43: 391
[3] Wang Z, Zhao H B, Wu Z M, et al. Analysis on corrosion of condenser tube in a marine heat exchanger [J]. Mater. Prot., 2019, 52(9): 189
[3] 王 钊, 赵宏博, 伍志明 等. 某船用换热器冷凝管腐蚀原因分析 [J]. 材料保护, 2019, 52(9): 189
[4] Cheng D B, Guo Y, Liu X H, et al. Studies on corrosion and protection of heat exchange tubes of B30 copper-nickel alloy [J]. Dev. Appl. Mater., 2020, 35(1): 84
[4] 程德彬, 郭 悦, 刘雪辉 等. B30铜镍合金换热管腐蚀与防护研究进展 [J]. 材料开发与应用, 2020, 35(1): 84
[5] Liu P, Chen Y Y. Progress research on evolution and failure behavior of surface coating of B30 copper-nickel alloy pipe [J]. Dev. Appl. Mater., 2023, 38(6): 1
[5] 刘 鹏, 陈雨雨. B30铜镍合金管材表面膜层演化及失效行为研究进展 [J]. 材料开发与应用, 2023, 38(6): 1
[6] Wang J M, Yang H D, Du M, et al. Corrosion of B10 Cu-Ni alloy in seawater polluted by high concentration of NH 4 + [J]. J. Chin. Soc. Corros. Prot., 2021, 41: 609
[6] 王家明, 杨昊东, 杜 敏 等. B10铜镍合金在高浓度NH 4 + 污染海水中腐蚀研究 [J]. 中国腐蚀与防护学报, 2021, 41: 609
[7] Jin T Z, Zhang W F, Li N, et al. Surface characterization and corrosion behavior of 90/10 copper-nickel alloy in marine environment [J]. Materials, 2019, 12: 1869
[8] Wu L, Ma A L, Zhang L M, et al. Erosion-corrosion behavior of 90/10 and 70/30 Copper-Nickel tubes in 1wt%NaCl solution [J]. Metals, 2023, 13: 401
[9] MODUK-DEF STAN 02-781 Protection of sea-water systems pipework and heat exchanger tubes in HM surface ships and submarines [S]. 2018
[10] Chen H L, Ma L, Huang G S, et al. Effect of dissolved oxygen and flow rate of seawater on film formation of B30 Cu-Ni alloy [J]. J. Chin. Soc. Corros. Prot., 2022, 42: 724
[10] 陈翰林, 马 力, 黄国胜 等. 溶解氧和流速对B30铜镍合金在海水中成膜的影响 [J]. 中国腐蚀与防护学报, 2022, 42: 724
[11] Gudas J P, Hack H P. Sulfide induced corrosion of copper nickel alloys [J]. Corrosion, 1979, 35: 67
[12] Al-Hajji J N, Reda M R. The corrosion of copper-nickel alloys in sulfide-polluted seawater: The effect of sulfide concentration [J]. Corros. Sci., 1993, 34: 163
[13] Macdonald D D, Syrett B C, Wing S S. The corrosion of Cu-Ni alloys 706 and 715 in flowing sea water. II-Effect of dissolved sulfide [J]. Corrosion, 1979, 35: 367
[14] Syrett B C. The mechanism of accelerated corrosion of copper-nickel alloys in sulphide-polluted seawater [J]. Corros. Sci., 1981, 21: 187
[15] Beccaria A M, Poggi G, Traverso P, et al. A study of the de-alloying of 70Cu-30Ni commercial alloy in sulphide polluted and unpolluted sea water [J]. Corros. Sci., 1991, 32: 1263
[16] Song H Q, Zhou J, Wang Y M. Failure analysis of B30 alloy tube used for vessel auxiliary condenser in seawater [J]. Corros. Prot., 2017, 38: 151
[16] 宋泓清, 周 娟, 王永明. 船用辅冷凝器B30合金管腐蚀失效分析 [J]. 腐蚀与防护, 2017, 38: 151
[17] Ekerenam O O, Emori W, Ma A L, et al. Corrosion studies of 90Cu-10Ni alloy tubes in simulated sulfide-polluted seawater under dynamic flow conditions [J]. Saf. Extreme Environ., 2023, 5: 221
[18] Li G X, Xing H Y, Du M, et al. Accelerated corrosion of 70/30 copper-nickel alloys in sulfide-polluted seawater environment by sulfide [J]. J. Mater. Res. Technol., 2024, 30: 8620
[19] Yin T F, Meng S, Zhao Y, et al. Modeling of the corrosion behavior of B30 alloy in a deep-sea environment by using the response surface methodology [J]. Mater. Corros., 2024, 75: 174
[20] Qian F, Liu X, Cui R, et al. Corrosive study of B10/B30 copper-nickel alloys coupled pipeline in static seawater [J]. Adv. Compos. Hybrid Mater., 2025, 8: 113
[21] Yin T F, Tian C P, Zheng K Y, et al. Investigation of an efficient pre-immersion treatment of B30 alloy used for power systems in an aggressive deep-sea environment [J]. Corros. Sci., 2025, 251: 112925
[22] Ding K K, Liu S T, Cheng W H, et al. Corrosion behavior of T2 and B30 Cu-Ni alloy at different seawater depths of the South China Sea [J]. J. Mater. Eng. Perform., 2021, 30: 6027
[23] Wang J, Li H, Du M, et al. Study on mechanism underlying the acceleration of pitting corrosion of B30 copper-nickel alloy by sulfate-reducing bacteria in seawater [J]. Sci. Total Environ., 2024, 928: 172645
[24] Ezuber H M. Effect of temperature and thiosulphate on the corrosion behaviour of 90-10 copper-nickel alloys in seawater [J]. Anti-Corros. Methods Mater., 2009, 56: 168
[25] Deroubaix G, Marcus P. X-ray photoelectron spectroscopy analysis of copper and zinc oxides and sulphides [J]. Surf. Interface Anal., 1992, 18: 39
[26] Zhang R W, Zhu Z Y, Leng X, et al. Corrosion characteristic of Cu-10Ni-Fe x in 3.5%NaCl [J]. Int. J. Electrochem. Sci., 2018, 13: 11526
[27] den Daas H, Passacantando M, Lozzi L, et al. The interaction of Cu(100)-Fe surfaces with oxygen studied by X-ray photoelectron spectroscopy [J]. Surf. Sci., 1994, 317: 295
[28] Terlingen J G A, Feijen J, Hoffman A S. Immobilization of surface active compounds on polymer supports using a gas discharge process [J]. J. Biomater. Sci. Polym. Ed., 1993, 4: 31
[29] Losev A, Rostov K, Tyuliev G. Electron beam induced reduction of CuO in the presence of a surface carbonaceous layer: An XPS/HREELS study [J]. Surf. Sci., 1989, 213: 564
[30] Bhide V G, Salkalachen S, Rastog A C, et al. Depth profile composition studies of thin film CdS: Cu2S solar cells using XPS and AES [J]. J. Phys., 1981, 14D: 1647
[31] Gebhardt J E, McCarron J J, Richardson P E, et al. The effect of cathodic treatment on the anodic polarization of copper sulfides [J]. Hydrometallurgy, 1986, 17: 27
[32] Peisert H, Chassé T, Streubel P, et al. Relaxation energies in XPS and XAES of solid sulfur compounds [J]. J. Electron Spectrosc. Relat. Phenom., 1994, 68: 321
[1] 李伟华, 李中, 张丹妮, 徐大可. 微生物诱导矿化抑制金属腐蚀:机制、设计策略及展望[J]. 中国腐蚀与防护学报, 2025, 45(6): 1459-1473.
[2] 王立芳, 商孟超, 高希钰, 刘贵昌, 孙文. B30铜镍合金原始膜对其腐蚀的影响[J]. 中国腐蚀与防护学报, 2025, 45(6): 1575-1588.
[3] 王杰, 赵平平, 王春婷, 竺婷婷, 杨丽景, 宋振纶. TC4钛合金在含S2- 海水中的腐蚀磨损行为研究[J]. 中国腐蚀与防护学报, 2025, 45(6): 1764-1772.
[4] 范世林, 杜娟, 杨少丹, 周延军, 宋克兴, 张国赏, 岳鹏飞, 杨冉, 王晓军. Cu-15Ni-8Sn合金在含S2-3.5%NaCl溶液中的腐蚀行为[J]. 中国腐蚀与防护学报, 2025, 45(5): 1408-1416.
[5] 耿真真, 张钰柱, 杜小将, 吴汉辉. S2-Cl-316L奥氏体不锈钢的腐蚀钝化行为的协同作用[J]. 中国腐蚀与防护学报, 2024, 44(3): 797-806.
[6] 王华, 王英杰, 刘恩泽. Ni含量对Co-Al-W合金热腐蚀行为的影响[J]. 中国腐蚀与防护学报, 2023, 43(6): 1419-1426.
[7] 刘超, 陈天奇, 李晓刚. 低合金钢中夹杂物诱发局部腐蚀萌生机制的研究进展[J]. 中国腐蚀与防护学报, 2023, 43(4): 746-754.
[8] 陈翰林, 马力, 黄国胜, 杜敏. pH值、温度和盐度对B30铜镍合金在海水中成膜的影响[J]. 中国腐蚀与防护学报, 2023, 43(3): 481-493.
[9] 王瑾, 宁培栋, 刘倩倩, 陈娜娜, 张新, 肖葵. 模拟海洋大气环境中镀锌钢的腐蚀行为和机理[J]. 中国腐蚀与防护学报, 2023, 43(3): 578-586.
[10] 陈翰林, 马力, 黄国胜, 杜敏. 溶解氧和流速对B30铜镍合金在海水中成膜的影响[J]. 中国腐蚀与防护学报, 2022, 42(5): 724-732.
[11] 高秋英, 徐亦璇, 胡鹏伟, 姚田万, 齐文龙. 天然气再生塔底重沸器腐蚀与防护技术研究[J]. 中国腐蚀与防护学报, 2022, 42(4): 699-704.
[12] 张震, 吴欣强, 谭季波. 电化学噪声原位监测应力腐蚀开裂的研究现状与进展[J]. 中国腐蚀与防护学报, 2020, 40(3): 223-229.
[13] 王保杰,栾吉瑜,王士栋,许道奎. 镁合金应力腐蚀开裂行为研究进展[J]. 中国腐蚀与防护学报, 2019, 39(2): 89-95.
[14] 王玉昆, 刘静, 胡骞, 黄峰. S2-对A710钢在NaCl溶液中腐蚀行为的影响[J]. 中国腐蚀与防护学报, 2018, 38(3): 233-240.
[15] 周霄骋, 崔巧棋, 贾静焕, 刘智勇, 杜翠薇. Cl-浓度对316L不锈钢在碱性NaCl/Na2S溶液中SCC行为的影响[J]. 中国腐蚀与防护学报, 2017, 37(6): 526-532.