Please wait a minute...
中国腐蚀与防护学报  2009, Vol. 29 Issue (4): 306-311         
  研究报告 本期目录 | 过刊浏览 |
Ti3Al基合金表面两种Cr1-xAlxN(x=0.18, 0.47)涂层热腐蚀性能
朱明1;2;李美栓1;周延春1
1. 中国科学院金属研究所 沈阳材料科学国家(联合)实验室 沈阳 110016
2. 西安科技大学材料科学与工程学院 西安 710054
HOT CORROSION RESISTANCE OF Cr1-xAlxN COATINGS ON A Ti3Al BASED ALLOY IN DEPOSITED (Na2SO4+K2SO4) MOLTEN SALT AT 800 ℃
ZHU Ming1;2; LI Meishuan1; ZHOU Yanchun1
1. Shenyang National Laboratory for Materials Science; Institute of Metal Research; Chinese Academy of Sciences; Shenyang 110016
2. College of Materials Science and Engineering; Xi’an University of Science and Technology; Xi’an 710054
引用本文:

朱明 李美栓 周延春. Ti3Al基合金表面两种Cr1-xAlxN(x=0.18, 0.47)涂层热腐蚀性能[J]. 中国腐蚀与防护学报, 2009, 29(4): 306-311.
, . HOT CORROSION RESISTANCE OF Cr1-xAlxN COATINGS ON A Ti3Al BASED ALLOY IN DEPOSITED (Na2SO4+K2SO4) MOLTEN SALT AT 800 ℃[J]. J Chin Soc Corr Pro, 2009, 29(4): 306-311.

全文: PDF(1428 KB)  
摘要: 

利用磁控反应溅射的方法在Ti3Al基合金表面制备了两种不同铝含量的Cr0.82Al0.18N与Cr0.53Al0.47N涂层,测试了这两种涂层在800 ℃(Na2SO4 + 25 mass %K2SO4)熔融盐膜下的热腐蚀动力学,并采用X射线衍射仪和带能谱的扫描电镜分析腐蚀产物相组成以及微观结构。结果表明,两种涂层均可降低Ti3Al基合金的热腐蚀速率;涂层热腐蚀产物主要为具有保护性的Cr2O3和θ-Al2O3混合氧化膜,θ-Al2O3的含量随着涂层中Al含量上升递增;和-θ-Al2O3相比,Cr2O3在熔融硫酸盐中的稳定性更好,Cr0.82Al0.18N涂层抗热腐蚀性能优于Cr0.53Al0.47N涂层。

关键词 : Cr1-xAlxN涂层,  热腐蚀,  Ti3Al基合金    
Abstract:

Cr0.82Al0.18N and Cr0.53Al0.47N coatings were deposited on a Ti3Al based alloy by reactive magnetron sputtering method. Hot corrosion of these two coatings in 75 mass % Na2SO4+25 mass % K2SO4 molten salt at 800 ℃ was performed in a Setsys 16/18 thermoanalyzer. The phase compositions of the corrosion products were identified by X-ray diffractometer (XRD). Both the surface and cross-sectional morphologies of the samples were observed by a scanning electron microscope (SEM). The results showed that both Cr0.82Al0.18N and Cr0.53Al0.47N can reduce the hot corrosion rate of the Ti3Al based alloy and their hot corrosion resistance decreases with increasing aluminum content; the main corrosion products of the coatings are Cr2O3 and θ-Al2O3 and the amount of θ-Al2O3 in the corrosion products is proportional to the Al content in the coating. The better hot corrosion resistance of Cr0.82Al0.18N coating can attribute to the high stability of Cr2O3 in the molten salt.

Key words: Cr1-xAlxN coatings    Hot corrosion    Ti3Al based alloy
收稿日期: 2008-12-15     
ZTFLH: 

TG172.62

 
基金资助:

国家自然科学基金资助项目(50771099)

作者简介: 朱明,1978年生,博士,研究方向为材料的高温腐蚀及表面改性

[1] Xu X J, Xu L H, Xin J P, et al. Pilot processing and microstructure control of high Nb containing alloy[J]. Intermetallics, 2005, 13:337-341
[2] Yoshihara M, Miura K. Effects of Nb addition on the oxidation behavior of Ti-Al[J]. Intermetallics, 1995, 3: 357-363
[3] Gauthier V, Dettenwanger F, Schutze M, et al. Oxidation resistant aluminide coatings on γ-Ti-Al[J]. Oxid. Met., 2003, 59:233-255
[4] Kuang S C. High temperature coating for titanium alumindes using the pack-cementation technique[J]. Oxid. Met.,1990, 34: 217-228
[5] Nishimoto T, Izumi T, Hayashi S, et al.Two-step Cr and Al diffusion coating on Ti-Al at high temperature[J].Intermetallics, 2003, 11: 225-235
[6] Katsman A, Ginzburg A,Werber T, et al. Nickel-aluminide coating of Ti-Al by a two-stage process[J]. Surf. Coat. Technol., 2000, 127: 219-222
[7] Koo C H, Yu T H. Pack cementation coatings on Ti3Al-Nb alloys to modify the high temperature oxidation properties[J]. Surf. Coat. Technol., 2000,126: 171-180
[8] Tang Z L, Wang F H, Wu W T. Effect of MCrAlY overlay coatings on oxidation resistance of Ti-Al intermetallics[J].Surf. Coat. Technol., 1998, 99: 248-252
[9] Li Z W, Gao W, Yoshihara M, et al. Improving oxidation resistance of Ti3Al and Ti-Al intermetallic compounds with electro-spark deposited coatings[J].Mater. Sci. Eng., 2003, A347: 243-252
[10] Wang F H, Guan C H,Tang Z L, et al. Effect of sputtered Ti-AlCr coatings on oxidation and hot corrosion resistance of Ti-24Al-14Nb-3V[J]. J. Mater. Sci.Technol., 2001, 17: 501-506
[11] Xi Y J, Wang F H, He L L.Protective effect of the sputtered Ti-AlCrAg coating on the high temperature oxidation and hot resistance of Ti-Al-Nb alloy[J]. J.Mater. Sci. Technol., 2004, 20: 724-727
[12] Zhou C G., Yang Y, Gong S K, et al. Effect of Ti-Al-Cr coatings on the high temperature oxidation behavior of Ti-Al based alloy[J]. Mater. Sci. Eng., 2001,307: 182-187
[13] Leyens C, Peters M, Hovsepian P Eh, et al.Novel coating\linebreak system produced by the combined cathodic arc/unbalanced magnetron sputtering environment protection of titanium[J]. Surf. Coat. Technol., 2002, 155: 103-111
[14] Banakh O, Schmid P E, Sanjines R, et al. High-temperature oxidation resistance of Cr1-xAlxN thin films deposited by reactive magnetron sputtering[J]. Surf. Coat. Technol., 2003, 163-164: 57-61
[15] Zhu M, Li M S, Zhou Y C. Improvment on the oxidation resistance of a Ti3Al based alloy by Cr1-xAlxN(0≤x≥0.47) coatings[J]. J Mater.Sci. Technol., 2007, 23, 373-378
[16] Zhu M, Li M S, Zhou Y C. Oxidation resistance of Cr1-xAlxN(0.18≤x≥0.47) coatings on K38G superalloy at 1000~1100 ℃ in air[J]. Surf. Coat. Technol.,2006, 201: 2878-2886
[17] Li T P, Yin X H, Li M S, et al.Oxidation resistance of a Cr0.50Al0.50N coating prepared by magnetron sputtering on alloy K38G[J]. Oxid. Met., 2007, 68:193-210
[18] Qian Y H. Studies on the high temperature corrosion behaviors of several alloys and the effects of rare earth elements and tensile load[D]. Shenyang: Institute of Metal Research, Chinese Academy of Sciences, 2002
(钱余海. 几种合金高温腐蚀行为与稀土、外应力影响机制研究[D].沈阳:中国科学院金属研究所,2002)
[19] Eliaz N, Shemesh G,Latanision R M. Hot corrosion in gas turbine component[J]. Eng.Fall. Anal., 2002, 9: 31-43
[20] Rapp R A. Hot corrosion of materials: a fluxing mechanism[J]. Corros. Sci., 2002, 44: 209-221

[1] 杨鑫, 车欣, 卢玉章, 黄亚奇, 王栋, 申健. 一种低Re二代单晶高温合金的热腐蚀行为研究[J]. 中国腐蚀与防护学报, 2026, 46(4): 1159-1168.
[2] 彭文雅, 李帅, 李璞, 赵春玲, 鲍泽斌. (Ni, Pt)Al和NiCoCrAlYTa涂层对镍基单晶高温合金DD6抗热腐蚀性能的影响[J]. 中国腐蚀与防护学报, 2026, 46(2): 491-499.
[3] 张金宇, 李欣, 张磊, 陈志华, 杜雨昕, 冯贺鑫, 张雪, 张洋鹏, 林如山, 李瑛, 戎利建. 几种17Cr系不锈钢在氯化物蒸汽中的腐蚀行为研究[J]. 中国腐蚀与防护学报, 2026, 46(2): 576-582.
[4] 王乙初, 刘天龙, 张思倩, 赵利, 骆智超, 郑开宏. 含V、W高Mn奥氏体耐热钢在熔融Na2SO4 中的热腐蚀行为[J]. 中国腐蚀与防护学报, 2026, 46(2): 620-628.
[5] 周小包, 王子腾, 任延杰, 董少阳, 甘浪, 李聪. 激光粉末床熔融成形CoCrNi中熵合金的高温热腐蚀行为[J]. 中国腐蚀与防护学报, 2026, 46(1): 115-125.
[6] 杨潇文, 陈泽浩, 杨莎莎, 王群昌, 王金龙, 陈明辉, 王福会. 镍基单晶高温合金N5及其纳米晶涂层的短期热腐蚀行为研究[J]. 中国腐蚀与防护学报, 2026, 46(1): 252-260.
[7] 叶俊, 罗鑫, 镇咸生, 李新平, 谢云, 彭晓. Inconel 718合金在750 ℃下不同气氛中的氧化与热腐蚀行为研究[J]. 中国腐蚀与防护学报, 2025, 45(6): 1528-1536.
[8] 彭望, 陈荐, 杨凌旭, 刘会军, 梁建平, 曾潮流. NaCl对347H和GH3539在熔融硝酸盐中热腐蚀行为的影响[J]. 中国腐蚀与防护学报, 2025, 45(6): 1610-1618.
[9] 白英雄, 王艳丽, 李相伟, 吴泽峰, 张书彦. 热处理对激光选区熔化GH4099镍基高温合金900 ℃下(75%Na2SO4 + 25%NaCl)热腐蚀行为的影响[J]. 中国腐蚀与防护学报, 2025, 45(6): 1709-1716.
[10] 赵欣宇, 刘恩泽, 张功, 赵媛, 宁礼奎, 信昕, 贾丹, 刘伟华, 谭政. 不同温度下DD10合金钎焊接头热腐蚀行为研究[J]. 中国腐蚀与防护学报, 2025, 45(5): 1361-1370.
[11] 张勇康, 翟海民, 李旭强, 李文生. Fe基非晶涂层在Na2SO4 + K2SO4 和Na2SO4 +NaCl混合盐中的热腐蚀行为研究[J]. 中国腐蚀与防护学报, 2025, 45(1): 92-102.
[12] 黄勤英, 李彧卓, 阳颖飞, 任盼, 王启伟. Pt改性共晶高熵合金AlCoCrFeNi2.1 热腐蚀行为研究[J]. 中国腐蚀与防护学报, 2025, 45(1): 115-126.
[13] 王粤, 耿树江, 王金龙, 王福会, 孙清云, 吴勇, 夏思瑶. K444合金表面CVD渗铝涂层耐高温95%Na2SO4 + 5%NaCl腐蚀行为研究[J]. 中国腐蚀与防护学报, 2025, 45(1): 127-136.
[14] 喻政, 陈明辉, 王金龙, 杨莎莎, 王福会. 煤灰中碱金属硫酸盐和氯盐含量对HR3C和渗铝HR3C不锈钢腐蚀行为的影响[J]. 中国腐蚀与防护学报, 2024, 44(6): 1389-1398.
[15] 张金龙, 付广艳, 宁礼奎, 刘恩泽, 谭政, 佟健, 郑志. 两种热处理状态的镍基单晶高温合金在900℃下(Na2SO4 + NaCl)混合盐中热腐蚀行为研究[J]. 中国腐蚀与防护学报, 2024, 44(6): 1625-1632.