Al,Cr,Ni和RE对Ag-Cu钎料氧化行为的影响

中国腐蚀与防护学报

1992, Vol. 12

Issue (2): 164-168

研究报告

本期目录 | 过刊浏览

Al,Cr,Ni和RE对Ag-Cu钎料氧化行为的影响

冼爱平;斯重遥;周龙江;沈嘉年;李铁藩

中国科学院金属研究所;中国科学院金属研究所;中国科学院腐蚀科学开放研究实验室;中国科学院腐蚀科学开放研究实验室;中国科学院腐蚀科学开放研究实验室

THE EFFECT OF Al, Cr Ni AND RE ON OXIDATION BEHAVIORS OF Ag-Cu EUTECTIC BASED ACTIVE BRAZING ALLOY

Xian Aiping; Si Zhongyao (Institute of Metal Research; Chinese Academy of Sciences)Zhou Longjiang; Shen Jianian and Li Tiefan (Corrasion Science Laboratory; Chinese Academy of Sciences)

全文: PDF(391 KB)

摘要: <正> 一、前言随着精细陶瓷材料的研究和应用所取得的巨大进展,金属与陶瓷的连接已成为急待解决的关键问题。由于普通金属钎料对陶瓷表面不浸润,因而许多工作集中在添加少量的钛或锆以改善钎料在陶瓷表面的可润湿性。其中特别是添加5at％Ti的Ag-Cu共晶钎料,因其综合性能优越,而最有发展前途。鉴于结构陶瓷主要在高温条件下使用,所以金属/陶瓷接头

Abstract：The oxidation behavior of Ag-Cu eutectic based active brazing alloys is studied by means of TGA, DTA, sessile drop method and X-ray diffraction technique. The results show that although the oxidation resistance of Ag-Cu eutectic-5at%Ti alloy at 873K is very poor, it can be improved by the addition of Al(5at%) without loss of its excellent wettability (contact angle 15° on sialon ceramic at 1150K for 5min). The oxidation kinetics behavior of the alloy with Al addition does not follow the parabolic law. In fact, the growth of the oxide film on the alloy becomes extremely slow after oxidation for 20 hours at 873K. The beneficial effect of aluminum can be attributed to the formation of an adhesive, protecive oxide film of CuAl_2O_4 on the alloy surface. As compared with the above results, the addition of Cr, Ni or RE is not effective in the improvement of oxidation resistance of the Ag-Cu-Ti brazing alloy.

收稿日期: 1992-04-25

基金资助:国家自然科学基金;;中国科学院沈阳分院理化测试中心为EDAX分析提供了部分资助

	服务

	把本文推荐给朋友
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	冼爱平
	斯重遥
	周龙江
	沈嘉年
	李铁藩
44.8K

引用本文:

冼爱平;斯重遥;周龙江;沈嘉年;李铁藩. Al,Cr,Ni和RE对Ag-Cu钎料氧化行为的影响[J]. 中国腐蚀与防护学报, 1992, 12(2): 164-168.
. THE EFFECT OF Al, Cr Ni AND RE ON OXIDATION BEHAVIORS OF Ag-Cu EUTECTIC BASED ACTIVE BRAZING ALLOY. J Chin Soc Corr Pro, 1992, 12(2): 164-168.

链接本文:

https://www.jcscp.org/CN/ 或 https://www.jcscp.org/CN/Y1992/V12/I2/164

[1] NaKa, M., Asami, K., et al., Trans. JWRI, 12． 145(1983)
[2] NaKa, M., and Okamoto, T., Trans, JWRI. 14, 29(1985)
[3] Moorhead, A. J., Weld. J., 62, 17(1983)
[4] Moorhead, A. J., and Keating, H., Weld. J., 65, 17(1986)
[5] Nicholas, M. J., et al., J. Mater. Sci., 15, 2197(1980)
[6] Kapoor, R. R., and Eagar, T. W., Metall. Trans., 20B, 919(1989)
[7] Mizuhara, H., and Mally, K., Weld. J., 64, 27(1985)
[8] Mizuhara, H., US Pat. No. 4591535, 1986
[9] Kapoor, R. R., and Eagar, T, W., J. Am. Ceram. Soc., 72, 448(1989)
[10] Xian. A. P., and Si, Z. Y., J. Mater. Sci., 25, 4483(1990)
[11] Kapoor, R. R., and Eagar, T. W., "Brazing Alloy Design for Metal/Ceramic Joints", Presented At 89th Annual Meeting of The American Ceramic Society, Pittsburgh, PA, April 28, 1987(Forum, Paper No. 12-F2-87)
[12] Huang, L. P., et al., Acta of Inorganic Mater. Sinica, 1(2) , 123(1986)
[13] Xian A. P. and Si Z. Y., J. Mater. Sci. Lett., 10, 246(1991)

No related articles found!

Viewed

Full text

Abstract

Cited

Shared

Discussed