Please wait a minute...
中国腐蚀与防护学报  2006, Vol. 26 Issue (3): 141-145     
  研究报告 本期目录 | 过刊浏览 |
热速处理对Mg-7Al-0.4Zn-0.2Mn合金耐腐蚀性能的影响
关绍康; 陈晶阳; 胡俊华; 任晨星; 杨卿
郑州大学材料科学与工程学院
INFLUENCE OF THERMAL-RATE TREATMENT ON THE CORROSION RESISTANCE OF Mg-7Al-0.4Zn-0.2Mn ALLOY
;;;;
郑州大学材料科学与工程学院
全文: PDF(487 KB)  
摘要: 测定自腐蚀电位、盐雾腐蚀速率和观察试样盐雾腐蚀表面形貌,研究了热速处理对Mg-7Al-0.4Zn-0.2Mn合金耐腐蚀性能的影响.结果表明:合金的腐蚀行为受到显微组织和铁含量的共同影响.过热温度(Ts)为810 ℃时,热速处理对合金耐腐蚀性能的改善作用并不大;过热温度为850 ℃时,热速处理显著细化了合金晶粒,β相的尺寸和间距变小,β相对α相腐蚀的阻碍作用增加,而且合金中的铁含量并没有提高,从而改善了合金在试验条件下的耐腐蚀性能;过热温度为890 ℃时,组织中存在热裂纹和显微疏松缺陷,合金含铁量显著增高,合金的耐腐蚀性能下降.相同的过热温度下,合金的耐腐蚀性能随着激冷速度(Vc)的增大而逐步改善.综合考虑合金的显微组织和耐腐蚀性能,优化的热速处理工艺为:Ts=850 ℃,Vc=2.0 ℃/s.此时,合金的耐腐蚀性能达到试验的最佳值,自腐蚀电位比未热速处理合金提高约15 mV,盐雾腐蚀速率比未热速处理合金降低21.9%.
关键词 Mg-7Al-0.4Zn-0.2Mn合金热速处理显微组织    
Abstract:The influence of thermal-rate treatment on the corrosion resistance of Mg-7Al-0.4Zn-0.2Mn(AZ70)alloy was studied by observing corrosion morphology,measuring corrosion potential and salt-spray corrosion rate.The results show that the corrosion behavior of AZ70 alloy depends on both its microstructure and iron content.When Ts is 850 ℃,grains are fined and the size of βphase and the distance betweenβphase pasticles are small.The corrosion barrier effect ofβ phase onαphase is enhanced and the iron content does not increase much at this temperature.So the corrosion resistance is improved.The corrosion resistance of AZ70 alloy falls off when Ts is 890 ℃,which attributes to the presence of microporosity,hot cracking and increase of iron content.At the same superheat-temperature,the corrosion resistance is improved with the increase of chilling rate.In comprehensive consideration of microstructure and corrosion resistance of AZ70 alloy,the optimal TRT process is that Ts=850 ℃ and Vc=2.0 ℃/s.In that case,the corrosion potential is 15 mV higher and the salt-spray corrosion rate is 21.9% lower than that of un-TRT treated alloy.
Key wordsMg-7Al-0.4Zn-0.2Mn(AZ70) alloy    Thermal-rate treatment(TRT)    Microstructure    Grain refinement    Corrosion
收稿日期: 2005-11-15     
ZTFLH:  TG146.2  
通讯作者: 关绍康      E-mail: q_autumn@163.com

引用本文:

关绍康; 陈晶阳; 胡俊华; 任晨星; 杨卿 . 热速处理对Mg-7Al-0.4Zn-0.2Mn合金耐腐蚀性能的影响[J]. 中国腐蚀与防护学报, 2006, 26(3): 141-145 .

链接本文:

https://www.jcscp.org/CN/Y2006/V26/I3/141

[1] 王凯, 易耀勇, 卢清华, 易江龙, 江泽新, 马金军, 张宇. 基于窄间隙焊接的热模拟峰值温度对Q690高强钢腐蚀行为的影响[J]. 中国腐蚀与防护学报, 2018, 38(5): 447-454.
[2] 牛振国, 郭浦山, 叶宏, 杨丽景, 许赪, 宋振纶. Zn-7Mg合金热处理显微组织演变及耐蚀性能研究[J]. 中国腐蚀与防护学报, 2017, 37(4): 347-353.
[3] 滕彧,陈旭,何川,王义闯,王冰. 显微组织对X70钢在含有硫酸盐还原菌的3.5%NaCl溶液中腐蚀行为的影响[J]. 中国腐蚀与防护学报, 2017, 37(2): 168-174.
[4] 张建春,左龙飞,蒋金洋,麻晗,宋丹. 耐海水腐蚀钢筋00Cr10MoV的组织结构及性能研究[J]. 中国腐蚀与防护学报, 2016, 36(4): 363-369.
[5] 苏艳,张伦武,钟勇. 5A90铝锂合金显微组织及海洋大气环境腐蚀行为[J]. 中国腐蚀与防护学报, 2016, 36(3): 260-266.
[6] 马旭,李全安,井晓天. 热处理对Mg-10Gd-2.5Nd-0.5Zr合金组织和耐蚀性能的影响[J]. 中国腐蚀与防护学报, 2016, 36(2): 143-149.
[7] 暨波,张新明,张卓夫,叶凌英,李文健. Yb对2519A铝合金抗剥落腐蚀性能的影响[J]. 中国腐蚀与防护学报, 2015, 35(3): 279-286.
[8] 张金龙, 屠礼明, 谢兴飞, 姚美意, 周邦新. Zr-1Nb-xGe合金在400 ℃过热蒸汽中耐腐蚀性能的研究[J]. 中国腐蚀与防护学报, 2014, 34(2): 171-177.
[9] 黄本生,江仲英,潘欢欢,袁鹏斌,刘清友. 热处理工艺对G105钻杆材料抗腐蚀性能的影响[J]. 中国腐蚀与防护学报, 2012, 32(1): 67-69.
[10] 米丰毅,王向东,汪兵,陈小平,彭云. 显微组织对低碳钢耐蚀性的影响[J]. 中国腐蚀与防护学报, 2010, 30(5): 391-395.
[11] 梁叔全,张勇,官迪凯,谭小平,唐艳,毛志伟. 轧制温度对铝阳极Al-Mg-Sn-Bi-Ga-In组织和性能的影响[J]. 中国腐蚀与防护学报, 2010, 30(4): 295-299.
[12] 陈美玲 刘元栋 杨莉 杨军 高宏. 改性纳米SiC粉体强化铸造奥氏体不锈钢耐点蚀性能的研究[J]. 中国腐蚀与防护学报, 2009, 29(6): 411-414.
[13] 贾瑞灵; 严川伟; 王福会 . 不同铝添加量对镁合金显微组织及大气腐蚀行为的影响[J]. 中国腐蚀与防护学报, 2007, 27(5): 269-273 .
[14] 汪淑英; 李具仓; 赵爱民 . 含铬高硅铁基合金组织和性能的研究[J]. 中国腐蚀与防护学报, 2007, 27(5): 292-295 .
[15] 张萍; 吴玉萍; 林萍华; 刘冠国 . 镍基喷焊层的抗气蚀性能研究[J]. 中国腐蚀与防护学报, 2006, 26(4): 197-201 .